Live Stoners Live Stoner Chat - Apr-Jun '24

Reader mode
McDee said:
The hole in this is soooo small it takes a few seconds of blowing through it to get air to come out. I wonder if it was like this always, and never noticed. It was a drop then nothing. Then a little later another drop. It's not like a flowing leak, but eventually it will be bigger. It looks like it's where the seems meet it was a little thin. I have bong that seeps where parts meet. It just slowly collects on the outside of the glass. You wipe it away, and then a little later there it is again. Never runs down the little bit of water like plugs the tiny holes. Very odd, but as wise old man to me "I've seen that fish before" lol. I don't have any good silicone all I have has hardened. I was think about giving it a spray with flex seal just not sure if that's safe with it coming into contact with water.
Click to expand...
You could hot knife it and melt the plastic back together :pass:
 
Good Morfnoevight All! EO'n'Dabs.

I felt like I needed to go to confession after eating these:

IMG_20240515_161341190.jpg :rofl: :rofl: :rofl:
 
McDee said:
The hole in this is soooo small it takes a few seconds of blowing through it to get air to come out. I wonder if it was like this always, and never noticed. It was a drop then nothing. Then a little later another drop. It's not like a flowing leak, but eventually it will be bigger. It looks like it's where the seems meet it was a little thin. I have bong that seeps where parts meet. It just slowly collects on the outside of the glass. You wipe it away, and then a little later there it is again. Never runs down the little bit of water like plugs the tiny holes. Very odd, but as wise old man to me "I've seen that fish before" lol. I don't have any good silicone all I have has hardened. I was think about giving it a spray with flex seal just not sure if that's safe with it coming into contact with water.
Click to expand...
Mine was like a drop every 10 or 15 seconds. Very hard to notice until quite a few drops built up with the lights off. I guess it was slow enough that it was just evaporating away before building up a puddle. My thought was to hit the auto parts store for vacuum line adaptors but seems they really don't carry much in that department anymore. I remember in the 80's getting anything and everything from 1/2 inch down to 1/16 inch in straights, 2 way, 3 way, 4 way and 8 way manifold.
 
Frankthetank said:
They sell plastic welding kits at harbor freight….that way you have filler…probably more expensive than a new piece…:haha:

Although jb weld would work, I suppose… :pass:
Click to expand...
JB has a plastic epoxy kit I used on a jeep steering pump res. Over 400 for the new pump, they don't just sell the res and for 7.99 I glooped it up and it was still holding 4 years later when I sold it.
 
McDee said:
I thought about that, melt a zip tie on it maybe. That is on the table, but kinda later option because I could end up melting the whole thing lol.
Click to expand...
I'd just just the main valve off, pull the connector, blow it out dry, silicone it and reinstall tomorrow. your pots won't dry out that much over 24 hours.
 
Reader mode
You must log in or register to reply here.

Similar threads

420Forever
  • Locked
Live Stoners Live Stoner Chat - Jan-Mar '24
2379 2380 2381
Replies
24K
Views
345K
420Forever
420Forever
420Forever
  • Locked
Live Stoners Live Stoner Chat - Apr-Jun '23
2983 2984 2985
Replies
30K
Views
348K
wwwillie
wwwillie
420Forever
  • Locked
Live Stoners Live Stoner Chat - Oct-Dec '22. 2700 pagez & 483k viewz
2699 2700 2701
Replies
27K
Views
685K
Mossy
Mossy
420Forever
  • Locked
Live Stoners Live Stoner Chat - Apr-Jun '22
1392 1393 1394
Replies
14K
Views
422K
420Forever
420Forever
Back
Top