Live Stoner Chat Live Stoner Chat - Apr-Jun '25

Fruitz, are you sure that’s sour cream and not Elton sauce?🤣
Aren’t u the guy who turns his harvests into fermented canna turds?? :shrug::crying::pighug:
 
Aren’t u the guy who turns his harvests into fermented canna turds?? :shrug::crying::pighug:

1747159935614.gif
 
Interesting suggestion. I can buy pure linalool terpene, so that might also be an option. When you say lavender, what form are you referring to? Dried flower, essential oil, extract of some sort? :cheers:
If I'm starting with 1oz flower, I add 1 little dried lavender flower or ½ big one.

I don't know how essential oil is made so I don't use that in case of residual solvents.

I got samples of pure terps to experiment with. It's pretty hard to dilute them right so I temporarily abandoned that.
 
This little girl is stretching and is starting to bud.
1000006470.jpg

I upped the nutes (and omitted the kelp/humic to keep ppm in zone) because I think the new growth is too light colored.

Seems for this strain the auto recommendations are too low for this stage and strain. I'll see what happens in the next day or 2.
 

Spain's freaky weather goes on...... :pass: ....



X-oholic ....:d5:..new word huh.......?........:biggrin:
 
Good Morfnoevight all you happy stoners!

Yes, I have a press. I have used both rosin and etoh extract done for carts decarbed for cbn. To get the THC to CBN, I decarb it for 4x what is normally needed at a given temperature. I have never had the results analysed, so have no real measure of CBN content after that. When you decarb for CBN, how do you do it, especially the time at time used rather than if you were decarbing normally.

So far, I do not notice a whole lot of difference in effects between the cbn decarb I do and the same strain decarbed normally. However my sleep medicating is still a work in progress. I have never managed to find consistent sleep results no matter how the stuff is processed. I have tried vaped flower, vaped rosin (decarbed for CBN, normal decarb for thc, and not decarbed before vaping), and vaped carts (from etoh extract, decarbed for THC, and decarbed for CBN). Sometimes it puts me to sleep all night, sometimes puts me down until I re-dose in the night, and sometimes (not often) does not seem to work well at all. It would be nice to find consistent all night sleep results, but perhaps that is too much to expect. :pighug:
The thing you need to do is rotate strains, when I need cannabis for pain relief rotating strains gives the best sustained relief.......... but there comes a day when your tolerance levels will get so high that a break is required. Hopefully by then the pain cycle is broken.

Here’s what I do….. you do need a small, oven safe vessel of some sort…. Found a very small bowl at Walmart that I use…..

Anyway, make rosin…. Use your best indica….

Next, in the bowl mentioned above, add the rosin, and make a tin foil lid…. Set the bowl with the lid on, on your rosin press plate that’s been preheated to 270f…..GENTLY close the rosin press so the top plate is touching the bowl…sandwiching the bowl in between….

Leave it for 70 minutes, then turn the press off, open the plates and remove….you’ll want to dump it into your final container while it’s still warm and viscous.

Dosing…… I dose at 6 pm for an 11pm bedtime…. I’ve played around, and found it takes a really long time to fully kick in….

I use my hot knife (dab tool) and put two globs (the most the tool will hold, twice) onto a small square of parchment paper, freeze that….then, using the hot knife again, pick up the frozen disc, drop it into my mouth and wash it down like a pill. The size of your dose may vary…..
Just make your rosin into chocolate bars, easy to titrate and enjoyable to ingest.
 
Back
Top