diy

I would like someone who makes their own fertilizer to check my math. I've learned Hydro Buddy and I have created my "ideal" nutrient recipe (in theory). However, I want to make sure I understand the formula for adding Disodium EDTA to chelate my Fe, Mn, Zn & Cu. From what I have extrapolated...

Hey everyone! Just dropping by to share a dry box I came up with. I was expecting to use the growbox for drying, but as I decided to chop one of my ladies, and I still have another one that is still finishing up, had to improvise a bit. Basically used a spare mattress box, made some cuttings...

2 OKay pairs left, 1 near-perfect & 1 total reject on the right side. Quarter Inch screws shall prove handy soon, eventually... Alt. source: https://i.postimg.cc/L6K291XC/Egzoset-s-Cust-VG-Pipe-Metal-Tops-Quarter-inch-Pilot-rods-480x480.png

Transvesal cuts are an early feature which may undermine the rest if too much error causes diviation from an ideal 90 degrees angle. Alt. source: https://i.postimg.cc/SR7TpsDs/Egzoset-s-Cust-VG-Pipe-Metal-Top-Transversal-Cut-MISALIGNMENT-as-cause-for-REJECTION-640x360.png

Best matching of axis alignments & transversal cuts don't always occur simultaneously. Alt. source: https://i.postimg.cc/N0S0vGzR/Egzoset-s-Cust-VG-Pipe-Metal-Tops-Transversal-Cut-Misalignments-AFTER-vs-BEFORE-touch-up-400x.png

These pilot rods provide low-friction rotating freedom while also working as an alignment tutor to limit direction changes until both holes join inside. Alt. source: https://i.postimg.cc/xjRSKT3g/Egzoset-s-Cust-VG-Pipe-Quarter-inch-Metal-Rod-as-Drill-Pilot-in-Whole-Bell-Saw-Cutters-for-alig.png

Doing more with less (using relatively basic tools)... Alt. source: https://i.postimg.cc/VNVWXhgf/Egzoset-s-Cust-VG-Pipe-Metal-Top-A-quarter-inch-Pilot-Hole-initially-drilled-from-Both-Sides-6.png

Hi guys! We just made a short video where we test the reflectivity of different materials commonly used in DIY grow spaces. Enjoy!

Hi all. New member, been growing almost 2 years. I posted in another feed about hydrometer mason jar lids because of my recent purchase of a used 3d printer and the ability to print a similar part. Yeah I can cut into existing lids but sure that I would cut myself. Printing them is much safer...

Hi folks, Kush here with yet another DIY ghetto grow. I will be growing Dinafem "Critical+ Autoflowering CBD" and Sweet Seeds "Sweet Skunk Auto" side by side. The beans were soaked in water yesterday and today the Critical+ Autoflowering CBD showed a tap root and was placed directly in the 11...

I was looking for a smart DIY home system and found this. Does anybody know this system? I just saw this new video they published and it looks very nice for a small DIY home growbox https://www.supergreenlab.com/

Hi yall, will be posting here photos of my grow space and my grows. Kind of a journal. any advice or tip are super welcome. Just added the reflector for the light.

Hey all! I battled bud rot all last season, my climate is perfect for it, so I’m hoping this high tunnel will help my chances! I built this for under $200, it’s 16’x10’x8’, I’ve got 4 plants in beds and trying to figure out the others now. I will run a few autos out here through the season...

Hey all! I battled bud rot all last season, my climate is perfect for it, so I’m hoping this high tunnel will help my chances! I built this for under $200, it’s 16’x10’x8’, I’ve got 4 plants in beds and trying to figure out the others now. I will run a few autos out here through the season...

Howdy farmers! I recently tested the PPFD (umol/m2/s) of a few different household bulbs to figure out how they perform compared to each other at a certain height. As we (humans) can perceive a lamp to be very bright, plants can sometimes experience a different reality. I also tested a couple...

Hey afn nation! I am a long time photo outdoor grower. I just switched to indoor autoflower plants. I am an hvac Master technician and a master electrician. I built my tent from giveaway ductwrap from dollar general that they use to keep their frozen food cold. (Go to local store on delivery...

Good morning everyone! We'd like to introduce a new vendor company to the forum called MassTerpenes! https://massterpenes.com/ MassTerpenes creates and sells wax and rosin liquefiers and terpenes to add into mixtures and for creating vape cartridges! Some of the members of our test team...

This formula is beginner-friendly. Never made a cartridge before? Not to worry. Our mixing process is quick, easy, and mess-free: 1. To start, simply preheat your oven to 200F while preparing your materials. 2. Place your preferred concentrate in provided glass mixing vial. Assuming you are...

Okay so I got my order from mass terpenes and man they are cool and threw in a few extras. Syringe mixing container 5 ml of fruity pebbles. Anyway here is what I did. First I pressed some rosin from some Remo Chemo I got more but I used a half gram of it for this cartridge. I placed the...

Lets exchange information on making our own vape cartridges.