- Joined
- Sep 1, 2014
- Messages
- 13,081
- Reputation
- 5,396
- Reaction score
- 46,429
- Points
- 0
- Currently Smoking
- yo arse
[h=2]Hey the groff
I've not had the Arizer Solo myself but I do own several portable vapes and each has a different techniques to get the best from each unit.
I'm sure some Solo users will be able to give you some hints and tips but I though in the mean time I would post this advice on using the Solo from http://thecannabisgeek.com/arizer-solo-the-ultimate-guide-to-the-ultimate-vaporiser/
Vaping Technique[/h]To load the Solo it’s best to put your stem into the upside-down unit, and then flip it once it’s secure. The first time can be difficult as the glass appears not to fit, but warm it for a few cycles and it’ll become easier. I tend to start on setting number 2 (185c), as that’s the lowest temperature at which the cannabinoids boil. A few deep (slow, for 8-10 seconds) draws at that level and then I move up to the next. As with any type of inhalation, there’s no need to keep it in your lungs for more than 5 seconds, as it has little added effect. All in all I would say that I tend to get around 10 draws from a full chamber.
The chamber itself is relatively small, but this helps us not overload the vape and waste our product. I find that a full chamber can range from 0.05g to 0.1g, depending on a number of factors, including how damp the weed is, to how tightly it’s packed. I tend to sprinkle weed into the chamber and then tap it until it drops into any gaps. Avoid squashing it down with your fingers or you’ll experience poorer air flow. I’ve found that there are certain sweet spots when it comes to generating vapour. If you inhale whilst slowly turning the stem, you’ll notice the noise changes as air whizzes through. The more of a ‘whoosh’ sound you hear, the better the chance of getting a good draw with less resistance.
Ensure that the Solo has stopped flashing and is at the required level before you attempt to draw vapour. It’s very fast to warm-up, but it’s easy to get caught out, especially if it has just turned itself off automatically (which is does every 12 minutes), so keep your eye on the LED display. If you wish, you can remove your stem between use; many people claim this stops waste. At most this would be just a little waste, but it’s waste nonetheless.
[h=2]High Efficiency Mouthpieces[/h]Before I’d purchased the Solo I was already aware of a number of specialist mouthpieces which were aimed at improving airflow. Apparently the original stems can require quite a lot of suction to produce vapour, although I haven’t tried mine since I went straight for the Turbo, which you can buy very cheaply here. The difference is that it comes with just a gauze, rather than having several cut-out pieces from a solid piece of glass. It’s estimated to improve airflow by 30%, and I’ve found it works perfectly for me.
If you want to save the expense, I recommend getting the standard kit and purchasing the Turbo piece later, if you find you’re dissatisfied with those provided by Arizer. Whichever you choose, I would recommend that rather than grinding material so fine that particles come up the mouthpiece (a problem even on the Turbo, and worse with the original stems), you tear bits off by hand and drop them in the chamber. It’s slightly messier, but it stops pieces being so small as to get through the holes and into your mouth. However, this does diminish the hit you receive, so if the particles aren’t an issue, stick to grinding.
I've not had the Arizer Solo myself but I do own several portable vapes and each has a different techniques to get the best from each unit.
I'm sure some Solo users will be able to give you some hints and tips but I though in the mean time I would post this advice on using the Solo from http://thecannabisgeek.com/arizer-solo-the-ultimate-guide-to-the-ultimate-vaporiser/
Vaping Technique[/h]To load the Solo it’s best to put your stem into the upside-down unit, and then flip it once it’s secure. The first time can be difficult as the glass appears not to fit, but warm it for a few cycles and it’ll become easier. I tend to start on setting number 2 (185c), as that’s the lowest temperature at which the cannabinoids boil. A few deep (slow, for 8-10 seconds) draws at that level and then I move up to the next. As with any type of inhalation, there’s no need to keep it in your lungs for more than 5 seconds, as it has little added effect. All in all I would say that I tend to get around 10 draws from a full chamber.
The chamber itself is relatively small, but this helps us not overload the vape and waste our product. I find that a full chamber can range from 0.05g to 0.1g, depending on a number of factors, including how damp the weed is, to how tightly it’s packed. I tend to sprinkle weed into the chamber and then tap it until it drops into any gaps. Avoid squashing it down with your fingers or you’ll experience poorer air flow. I’ve found that there are certain sweet spots when it comes to generating vapour. If you inhale whilst slowly turning the stem, you’ll notice the noise changes as air whizzes through. The more of a ‘whoosh’ sound you hear, the better the chance of getting a good draw with less resistance.
Ensure that the Solo has stopped flashing and is at the required level before you attempt to draw vapour. It’s very fast to warm-up, but it’s easy to get caught out, especially if it has just turned itself off automatically (which is does every 12 minutes), so keep your eye on the LED display. If you wish, you can remove your stem between use; many people claim this stops waste. At most this would be just a little waste, but it’s waste nonetheless.
[h=2]High Efficiency Mouthpieces[/h]Before I’d purchased the Solo I was already aware of a number of specialist mouthpieces which were aimed at improving airflow. Apparently the original stems can require quite a lot of suction to produce vapour, although I haven’t tried mine since I went straight for the Turbo, which you can buy very cheaply here. The difference is that it comes with just a gauze, rather than having several cut-out pieces from a solid piece of glass. It’s estimated to improve airflow by 30%, and I’ve found it works perfectly for me.
If you want to save the expense, I recommend getting the standard kit and purchasing the Turbo piece later, if you find you’re dissatisfied with those provided by Arizer. Whichever you choose, I would recommend that rather than grinding material so fine that particles come up the mouthpiece (a problem even on the Turbo, and worse with the original stems), you tear bits off by hand and drop them in the chamber. It’s slightly messier, but it stops pieces being so small as to get through the holes and into your mouth. However, this does diminish the hit you receive, so if the particles aren’t an issue, stick to grinding.
so win win there.
